Beretta 92 Optics Ready Mount for Burris Fastfire, Vortex Venom / Viper by EGW
This mount fits:
Beretta 92 FS
Beretta 92 G
Beretta 92 FS Fusion
Beretta 92 Fusion Black
Beretta 92 Fusion Blu
Beretta 92 FS Inox
Beretta 92 A1
Beretta 92 FS Brigadier
Beretta 92 FS Brigadier Inox
Beretta 92 G Elite
Beretta 92 Compact
Beretta 92 Compact w/ Rail
Beretta 92 Compact with Rail Inox
Beretta 92 Vertec Inox
Beretta 92G-SD
Beretta 92X Centurion
Beretta 92X Compact
Beretta 92X Compact w/ Rail
Beretta 92X Full Size
Beretta 98 A1
Beretta 98 FS
Beretta 90 Series Inox
Beretta M9
Beretta M9 Exclusive
Beretta M9A1
Beretta M9A3
Beretta M9A3 Black
Beretta 98 FS Inox
This mount does not fit (including but not limited to):
Beretta 92 Optics Ready Models
Beretta 92 FS Centennial
Beretta 92 Performance
Beretta 92 Performance Defensive
Beretta 92 RDO Compact Y22
Beretta M9 A4 Centurion Y22
SPECIFICATIONS
Material: 7075 Aluminum
Coating: Matte Black Hardcoat
Overall Length: 1.811"
Overall Width: .99"
Torque Specs: 15 in/lbs
Mounting Hardware:
(2) 6-32 x 5/16" Button Head Screws - Requires 5/64 Wrench or Driver
(2) 6-32 x 3/8" Flat Head Screws - Requires 5/64 Wrench or Driver
(2) 6-32 x 5/16" Flat Head Screws - To Secure Plate to Insert - Requires 5/64 Wrench or Driver
(1) Dovetail Insert
Red Dot Fitment:
Vortex Viper
Vortex Venom
Burris Fast Fire 1, 2, 3, 4
Docter
ADE RD3-001
ADE RD3-002
ADE RD3-009
UTG Reflex Micro Dot
Crimson Trace CTS-1200
Crimson Trace CTS-1300
Sightmark Mini Shot
Sightmark Core Shot
The mounting screws require a 5/64" wrench and the set screws (when applicable) require a 1/16" wrench.
*All ADE mounts require 6-32 x 3/8" screws.
Please note: We have found that some red dots commonly found on Amazon such as the UTG and ADE may not hold the same tolerances as the red dots that this mount was initially created to work with. These dots may not fit properly on the posts on the plate. We would recommend either sending the red dot back for an exchange to whichever seller you purchased it from, or open up the holes in the bottom of the red dot to accommodate the pins.
Do you need to install a red dot mount on your Beretta 92? Our red dot mount allows you to easily install a red dot on your Beretta. Our Beretta 92 red dot sights mounts are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install.
Simply remove the rear sight on your gun and replace it with our mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take our mount off and replace your rear sight at any time. Mounting hardware included.
Installation Instructions
- Remove the rear sight*
- Install the EGW Sight Mount in the dovetail
- Tighten set screw (if applicable)
- Place the red dot sight on the EGW Sight Mount
(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
- Apply blue Loctite to the provided mounting screws
- Torque mounting screws to 15in/lbs
2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights
2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights
2 Flat Head Cap Screws - Provided to mount the Plate to the Dovetail
The screws that are included with this mount require a 5/64'' allen wrench for installation.
Modification of your firearm may nullify the manufacturer's warranty.
This product should be installed and checked by a qualified gunsmith.
No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
Click here to see a video from Vortex on how to install our red dot base on a slide.
