Ben Stoeger BSPS BOSS DOH Dropped Offset Holster Hanger Mount System
This hanger is adjustable yet stable. It will hold your holster in the position of your choosing allowing for a safe and secure draw. This holster hanger can be mounted ambidextrously making it appropriate for left and right handed shooters.
The holster can be mounted higher up, making it Single Stack legal if you desire.
This is just the holster hanger. Supply your own pouch. This is compatible with Blade Tech, GX Holster, LS Holsters, Weber Tactical and Comp Tac stuff.
What are the differences in the Belt Mount Options?
What are the differences in the Belt Mount Options?
We offer a few options for belt mounts on the Boss holster. The standard aluminum belt plate will come with all of the holsters regardless if you choose one of the options mounts. Something to consider if you go with a non-standard belt mount you may want to go with a shorter Offset Spacer like the 1/4" to stay withing the USPSA rules.
|
The Boss Standard Belt Mount is included with all orders. This belt plate is cut for a standard 1.5" competition belt (DAA, CR Speed, Ghost). The spacing between the screws will accommodate a 1.75" belt. |
The Blade-Tech Tek-Lok Belt Mount is a great Quick Detach option. These mounts are adjustable and can accommodate 1.25"-2" belts We generally recommend going with the 1/4" offset spacer option with this mount. |
|
The Comp-Tac PLM Belt Mount is a great Quick Detach option. These mounts are adjustable and can accommodate 1.25"-2" belts We generally recommend going with the 1/4" offset spacer option with this mount |
The Safariland QLS Belt Mount work with the QLS Receiver. You can quickly swap holsters when using the Safariland QLS system. This option includes the fork only. We generally recommend going with the 1/4" offset spacer option with this mount |
Which Offset length should I choose?
This refers to the length of the spacers between the long Boss plate and the Y-Plate that attaches to the holster. The 1/2" spacers are a pretty safe bet for most firearms out there to keep you within the rules for USPSA.
If you go with one of the options mounts (Tek-Lok, PLM, ELS) we would recommend choosing the 1/4" spacers to keep your holster within the rules for USPSA.
We have seen the 3/4" work well for most models, and may work with Tek-Lok & PLM mounts.
We have found the 1" spacers to work with most models but you should measure your setup to insure it falls within the USPSA rules.
You can always just buy the Spacer Hardware Kit here and try the other options.
What is the optional Baller Ball Joint?
Upgrade your Boss Holster Hanger with the new release from Shockbottle, the Boss Baller Ball Joint.
This ball joint upgrade for your Boss Hanger allows you to adjust the angle of the holster and still raise and lower it as you expect with the Boss Holster Hanger.
You can use the ball joint instead of the spacers on your current rig!
 |
 |
What is the optional Aluminum Thigh Pad?
Comfort and Adjustability Boss Holster Hanger Aluminum Thigh Pad features a unique design that allows you to adjust the spacing of your Boss holster hanger to your personal preference, providing maximum comfort and flexibility.
 |
 |
How to do mount a Safariland QLS Fork or Receiver?
The versatile Boss Holster Hanger is designed to offer multiple mounting options for the Safariland QLS system. It facilitates the attachment of the Safariland QLS Fork to the long plate that is included in the kit, thereby eliminating the need for any additional parts or unique configurations.
For those seeking a flexible mounting solution that allows for easy swapping of holsters while keeping the hanger firmly attached to your belt, we offer the Safariland Y-Plate option. With this, you can conveniently mount the Safariland QLS Receiver to the Y-Plate, as demonstrated in the photographs below.
This powerful combination of utility and adaptability makes the Boss Holster Hanger an essential tool for enhancing your holster mounting experience.
 |
 |
 |
Instructions
1. Attach Y-plate to holster body through three large holes on the Y-plate using supplied short round-head screws to the backers included with your holster.
2. Attach Y-plate to slotted hanger plate using supplied long screws and spacers (do not install lock washers yet). Screw heads should be on the rounded side of the hanger plate, one screw in a center hole and the other in the corresponding curved slot.
3. Hold belt inside belt plate cutout and install onto main hangar plate with 4 flat-head screws, solidly mounting holster and hanger to belt.
4. Test location of holster with unloaded firearm. Adjust to preferred height and tilt by changing screw positions on the main hangar plate and Y-plate. Verify position meets rule requirements
5. Mark position of long screws lightly with a pencil and then remove and re-install the long screws with a lock washer underneath the screw heads. Apply threadlocker to all screws.
* Verify firearm position meets appropriate rule requirements
- #1:
- Attach Y-plate to holster body through three large holes on the Y-plate using short round-head screws
- #2:
- Attach Y-plate to slotted hanger plate using long screws and spacers (do not install lock washers yet). Screw heads should be on the rounded side of the hanger plate, one screw in a center hole and the other in the corresponding curved slot.
- #3:
- Hold belt inside belt plate cutout and install onto main hangar plate with 4 flat-head screws, solidly mounting holster and hanger to belt.
- #4:
- Test location of holster with unloaded firearm. Adjust to preferred height and tilt by changing screw positions on the main hangar plate and Y-plate. Verify position meets rule requirements
- #5:
- Mark position of long screws lightly with a pencil and then remove and re-install the long screws with a lockwasher underneath the screw heads. Apply threadlocker to all screws.
139 Reviews
-
Very good product
Just like a previous reviewer, the only issues I can find are 1. make the spacers from a bit harder material. 2. Include different size spacers. I needed to order the 3/4" spacers afterwards. Fortunately, I was making another order anyway.
-
Good product
Overall good and solid great range of adjustability. I would suggest to make the spacers from a bit harder material. If tightening the adjustment screws solidly the spacers slightly compress. I would also suggest to supply the kit with a couple of different spacer lenghts since we all prefer to have a little bit different angles. I solved this by using regular washers to adjust the spacer lengths. The quality generally speaking is really good. With some small tweaks i would give it full score.
-
perfect match for bladetech holsters
recently purchased for SS and CZ TS Blade-tech holsters and should have done so long ago. easy set up and works as advertised.
-
Great hanger system
If you're contemplating getting this hanger system, I say, just do it. This thing is amazing, and you absolutely will not be disappointed.
-
awesome product
The boss hanger is amazining. I bought the hanger to sturdy up my blade tech holster and it does and a lot more. Really gets the holster up as to accommodate my single stack. I would highly recline d this product to anyone in competitive shooting or anyone wanting a sturdy hanger.
-
The boss is Boss!
lots of adjustment, worked for my single stack 45.
-
The BOSS hanger works!
I have used the DOS that you can get from Blade-tec. While it works OK, there is too much flex in it. The BOSS hanger is very rigid and keeps your pistol in exactly the same position every time. It was very easy to set up. I highly recommend this hanger for your holster.
-
Holster Hanger
Bought a Bladtech holster, mount that came with horrible. Was turned on to this Hanger, after install there is no way that I can do without. Very well designed and works like it supposed to.
-
Best of the Best
Excellent!
-
recommemded
The reviews are true this product provides a rock solid platform. Fit great on my Com Tac International holster, I will be buying another one for my single stack rig.
-
Perfect Attachment for Com-Tec Holsters
The hardware worked perfectly with the Com-Tec Holster I have. I had to look at the previous unit I bought before hand to use as a guide to assemble the unit. It was not to difficult to figure out and when completed it made drawing the weapon easy as grease on a stuck bolt. Did you ever think of a unit for open guns? I know I would buy one in a New York minute.
-
My Second one
I bought my first one for USPSA SS and this one was for USPSA production. I am using blade tech holsters for both. I found they increase the stability of the holster and in my opinion the draw is much more consistant.
