Ben Stoeger BSPS BOSS DOH Dropped Offset Holster Hanger Mount System
This hanger is adjustable yet stable. It will hold your holster in the position of your choosing allowing for a safe and secure draw. This holster hanger can be mounted ambidextrously making it appropriate for left and right handed shooters.
The holster can be mounted higher up, making it Single Stack legal if you desire.
This is just the holster hanger. Supply your own pouch. This is compatible with Blade Tech, GX Holster, LS Holsters, Weber Tactical and Comp Tac stuff.
What are the differences in the Belt Mount Options?
What are the differences in the Belt Mount Options?
We offer a few options for belt mounts on the Boss holster. The standard aluminum belt plate will come with all of the holsters regardless if you choose one of the options mounts. Something to consider if you go with a non-standard belt mount you may want to go with a shorter Offset Spacer like the 1/4" to stay withing the USPSA rules.
|
The Boss Standard Belt Mount is included with all orders. This belt plate is cut for a standard 1.5" competition belt (DAA, CR Speed, Ghost). The spacing between the screws will accommodate a 1.75" belt. |
The Blade-Tech Tek-Lok Belt Mount is a great Quick Detach option. These mounts are adjustable and can accommodate 1.25"-2" belts We generally recommend going with the 1/4" offset spacer option with this mount. |
|
The Comp-Tac PLM Belt Mount is a great Quick Detach option. These mounts are adjustable and can accommodate 1.25"-2" belts We generally recommend going with the 1/4" offset spacer option with this mount |
The Safariland QLS Belt Mount work with the QLS Receiver. You can quickly swap holsters when using the Safariland QLS system. This option includes the fork only. We generally recommend going with the 1/4" offset spacer option with this mount |
Which Offset length should I choose?
This refers to the length of the spacers between the long Boss plate and the Y-Plate that attaches to the holster. The 1/2" spacers are a pretty safe bet for most firearms out there to keep you within the rules for USPSA.
If you go with one of the options mounts (Tek-Lok, PLM, ELS) we would recommend choosing the 1/4" spacers to keep your holster within the rules for USPSA.
We have seen the 3/4" work well for most models, and may work with Tek-Lok & PLM mounts.
We have found the 1" spacers to work with most models but you should measure your setup to insure it falls within the USPSA rules.
You can always just buy the Spacer Hardware Kit here and try the other options.
What is the optional Baller Ball Joint?
Upgrade your Boss Holster Hanger with the new release from Shockbottle, the Boss Baller Ball Joint.
This ball joint upgrade for your Boss Hanger allows you to adjust the angle of the holster and still raise and lower it as you expect with the Boss Holster Hanger.
You can use the ball joint instead of the spacers on your current rig!
 |
 |
What is the optional Aluminum Thigh Pad?
Comfort and Adjustability Boss Holster Hanger Aluminum Thigh Pad features a unique design that allows you to adjust the spacing of your Boss holster hanger to your personal preference, providing maximum comfort and flexibility.
 |
 |
How to do mount a Safariland QLS Fork or Receiver?
The versatile Boss Holster Hanger is designed to offer multiple mounting options for the Safariland QLS system. It facilitates the attachment of the Safariland QLS Fork to the long plate that is included in the kit, thereby eliminating the need for any additional parts or unique configurations.
For those seeking a flexible mounting solution that allows for easy swapping of holsters while keeping the hanger firmly attached to your belt, we offer the Safariland Y-Plate option. With this, you can conveniently mount the Safariland QLS Receiver to the Y-Plate, as demonstrated in the photographs below.
This powerful combination of utility and adaptability makes the Boss Holster Hanger an essential tool for enhancing your holster mounting experience.
 |
 |
 |
Instructions
1. Attach Y-plate to holster body through three large holes on the Y-plate using supplied short round-head screws to the backers included with your holster.
2. Attach Y-plate to slotted hanger plate using supplied long screws and spacers (do not install lock washers yet). Screw heads should be on the rounded side of the hanger plate, one screw in a center hole and the other in the corresponding curved slot.
3. Hold belt inside belt plate cutout and install onto main hangar plate with 4 flat-head screws, solidly mounting holster and hanger to belt.
4. Test location of holster with unloaded firearm. Adjust to preferred height and tilt by changing screw positions on the main hangar plate and Y-plate. Verify position meets rule requirements
5. Mark position of long screws lightly with a pencil and then remove and re-install the long screws with a lock washer underneath the screw heads. Apply threadlocker to all screws.
* Verify firearm position meets appropriate rule requirements
- #1:
- Attach Y-plate to holster body through three large holes on the Y-plate using short round-head screws
- #2:
- Attach Y-plate to slotted hanger plate using long screws and spacers (do not install lock washers yet). Screw heads should be on the rounded side of the hanger plate, one screw in a center hole and the other in the corresponding curved slot.
- #3:
- Hold belt inside belt plate cutout and install onto main hangar plate with 4 flat-head screws, solidly mounting holster and hanger to belt.
- #4:
- Test location of holster with unloaded firearm. Adjust to preferred height and tilt by changing screw positions on the main hangar plate and Y-plate. Verify position meets rule requirements
- #5:
- Mark position of long screws lightly with a pencil and then remove and re-install the long screws with a lockwasher underneath the screw heads. Apply threadlocker to all screws.
139 Reviews
-
Must Have for Competition use
This makes your holster rock solid and draw consistent. I now have them on both my Production and Single Stack rig. Hands down the best hanger on the market.
-
Excellent product
I'm new to production after shooting limited and open for many years. After trying various options that didn't allow for much if any adjustment I found this product to work better than anything I've seen or found. It is very solid and allows for a great range of adjustment and is very comfortable also.
-
Must for USPSA Folks
I recently purchased the BOSS Hanger for a Comp-Tac Intl. holster that I use to shoot Production. I was recommended this by a friend who has been using this for about a year now. He said it will help with the draw and I wouldn't regret it. I can see he was right. I was able to get my best draws consistently to date at a recent practice day running some drills. This hanger has rigidity and is tunable to each shooter's preference in regards to cant and how far you wold like it to hang. This is a must for any Production or even a Limited shooter that uses a DOH. You will not be disappointed. A great product with free shipping. It doesn't get any better than that!
-
Best holster mounting system out there.
I'm currently running this system on my Single stack, Production, and Limited rig. It allows my to get a better, more complete grip on the pistol for faster deployment. This helped my drawstroke times tremendously. I'd recommend this product to anyone serious about competition.
-
Rock solid
I've only been using the Boss holster hanger for a short while, but so far I've been quite happy with the way it performed. It definitely provides a solid mounting point for your holster and has more than enough adjustability for the intended use. I'm glad I got it.
-
Excellent, But
You can hang just about any holster, angle it forward or backward, even tilt it in or out if you want. As long as you have a 1.5" belt! Alas, I use a 1.75" Safariland, so I milled the inside of the belt loop piece 45°, and it fits great ! Even able to have my custom NeuMount holster with my NeuMount Red Dot Sight Mount & RTS Sight.
-
Great Product.
I really like this product, very sturdy, with lots of adjustment/ fine tuning possibilities. Well made as well.
