Ben Stoeger BSPS BOSS DOH Dropped Offset Holster Hanger Mount System
This hanger is adjustable yet stable. It will hold your holster in the position of your choosing allowing for a safe and secure draw. This holster hanger can be mounted ambidextrously making it appropriate for left and right handed shooters.
The holster can be mounted higher up, making it Single Stack legal if you desire.
This is just the holster hanger. Supply your own pouch. This is compatible with Blade Tech, GX Holster, LS Holsters, Weber Tactical and Comp Tac stuff.
What are the differences in the Belt Mount Options?
What are the differences in the Belt Mount Options?
We offer a few options for belt mounts on the Boss holster. The standard aluminum belt plate will come with all of the holsters regardless if you choose one of the options mounts. Something to consider if you go with a non-standard belt mount you may want to go with a shorter Offset Spacer like the 1/4" to stay withing the USPSA rules.
|
The Boss Standard Belt Mount is included with all orders. This belt plate is cut for a standard 1.5" competition belt (DAA, CR Speed, Ghost). The spacing between the screws will accommodate a 1.75" belt. |
The Blade-Tech Tek-Lok Belt Mount is a great Quick Detach option. These mounts are adjustable and can accommodate 1.25"-2" belts We generally recommend going with the 1/4" offset spacer option with this mount. |
|
The Comp-Tac PLM Belt Mount is a great Quick Detach option. These mounts are adjustable and can accommodate 1.25"-2" belts We generally recommend going with the 1/4" offset spacer option with this mount |
The Safariland QLS Belt Mount work with the QLS Receiver. You can quickly swap holsters when using the Safariland QLS system. This option includes the fork only. We generally recommend going with the 1/4" offset spacer option with this mount |
Which Offset length should I choose?
This refers to the length of the spacers between the long Boss plate and the Y-Plate that attaches to the holster. The 1/2" spacers are a pretty safe bet for most firearms out there to keep you within the rules for USPSA.
If you go with one of the options mounts (Tek-Lok, PLM, ELS) we would recommend choosing the 1/4" spacers to keep your holster within the rules for USPSA.
We have seen the 3/4" work well for most models, and may work with Tek-Lok & PLM mounts.
We have found the 1" spacers to work with most models but you should measure your setup to insure it falls within the USPSA rules.
You can always just buy the Spacer Hardware Kit here and try the other options.
What is the optional Baller Ball Joint?
Upgrade your Boss Holster Hanger with the new release from Shockbottle, the Boss Baller Ball Joint.
This ball joint upgrade for your Boss Hanger allows you to adjust the angle of the holster and still raise and lower it as you expect with the Boss Holster Hanger.
You can use the ball joint instead of the spacers on your current rig!
 |
 |
What is the optional Aluminum Thigh Pad?
Comfort and Adjustability Boss Holster Hanger Aluminum Thigh Pad features a unique design that allows you to adjust the spacing of your Boss holster hanger to your personal preference, providing maximum comfort and flexibility.
 |
 |
How to do mount a Safariland QLS Fork or Receiver?
The versatile Boss Holster Hanger is designed to offer multiple mounting options for the Safariland QLS system. It facilitates the attachment of the Safariland QLS Fork to the long plate that is included in the kit, thereby eliminating the need for any additional parts or unique configurations.
For those seeking a flexible mounting solution that allows for easy swapping of holsters while keeping the hanger firmly attached to your belt, we offer the Safariland Y-Plate option. With this, you can conveniently mount the Safariland QLS Receiver to the Y-Plate, as demonstrated in the photographs below.
This powerful combination of utility and adaptability makes the Boss Holster Hanger an essential tool for enhancing your holster mounting experience.
 |
 |
 |
Instructions
1. Attach Y-plate to holster body through three large holes on the Y-plate using supplied short round-head screws to the backers included with your holster.
2. Attach Y-plate to slotted hanger plate using supplied long screws and spacers (do not install lock washers yet). Screw heads should be on the rounded side of the hanger plate, one screw in a center hole and the other in the corresponding curved slot.
3. Hold belt inside belt plate cutout and install onto main hangar plate with 4 flat-head screws, solidly mounting holster and hanger to belt.
4. Test location of holster with unloaded firearm. Adjust to preferred height and tilt by changing screw positions on the main hangar plate and Y-plate. Verify position meets rule requirements
5. Mark position of long screws lightly with a pencil and then remove and re-install the long screws with a lock washer underneath the screw heads. Apply threadlocker to all screws.
* Verify firearm position meets appropriate rule requirements
- #1:
- Attach Y-plate to holster body through three large holes on the Y-plate using short round-head screws
- #2:
- Attach Y-plate to slotted hanger plate using long screws and spacers (do not install lock washers yet). Screw heads should be on the rounded side of the hanger plate, one screw in a center hole and the other in the corresponding curved slot.
- #3:
- Hold belt inside belt plate cutout and install onto main hangar plate with 4 flat-head screws, solidly mounting holster and hanger to belt.
- #4:
- Test location of holster with unloaded firearm. Adjust to preferred height and tilt by changing screw positions on the main hangar plate and Y-plate. Verify position meets rule requirements
- #5:
- Mark position of long screws lightly with a pencil and then remove and re-install the long screws with a lockwasher underneath the screw heads. Apply threadlocker to all screws.
139 Reviews
-
Boss Hanger
Absolutely solid, a perfect hanger.
-
high quality build.
This makes for a very stable platform with a lot of adjustablity.
-
excellent quality product
very nice and sturdy hanger
-
Great Quality
Very early on in purchase, but the product was easy to install. Very sturdy with very little movement when drawing.
-
Back nut
I think that back nuts should be provided for the screws going into the Y attachment instead of having to use my backs from my bladetek belt connector. Otherwise it was as described.
-
I own 4 of them now
I think that says it all. They just do the job - easy to adjust, rock solid, no issues. I have two mounted with the BOSS hanger attachment on the belt, and two mounted to Blade Tech belt mounts (getting too many belts if you know what I mean).
-
This hanger is the BOSS
It almost has too much adjustability, but once I got it set the way I liked it, it is solid. I really like that it has enough range of adjustability to be useful in multiple divisions.
-
Boss Hanger says it all.
Love the Boss Hanger. Keeps everything in place to get a consistent draw each time. Would highly recommend.
-
Clearance for my thumb!
I shoot a Walther Q5 with a Vortex red dot. I originally purchased a Blade tech holster with their short drop and offset belt attachment using a tech lock fastener. The positioning was good, stability on the belt was just fair. The biggest problem was my thumb was cramped on the draw. I had to bend my thumb and then straighten it out after clearing the holster. The Boss Hanger solved that problem completely. I get a full firing grip, with my thumb extended, while still in the holster. The stability on the belt is also vastly superior to what the techlock clip provided. I'm very happy with this product and would recommend it to my friends.
-
Just buy it
It's what you need. It's great build quality and has great adjustability. Buy it.
-
Quality and Value
I am incredibly happy with this Product! I was also very happy with how quickly is arrived and the ease of assembly. I will be purchasing another one very soon!!
-
SO much better!
All I have ever used is a mydex holster with a teklok attatched directly to a belt. This makes the firearm ride very close to your body which isnt bad if you're super skinny. However just a few extra pounds makes it difficult ti get a good , quick grip on the gun. Even mote so if your shooting in the winter months with heavier clothing on. The BOSS hanger gets it the perfect distance away from my body. I love it!
