Ben Stoeger BSPS BOSS DOH Dropped Offset Holster Hanger Mount System
This hanger is adjustable yet stable. It will hold your holster in the position of your choosing allowing for a safe and secure draw. This holster hanger can be mounted ambidextrously making it appropriate for left and right handed shooters.
The holster can be mounted higher up, making it Single Stack legal if you desire.
This is just the holster hanger. Supply your own pouch. This is compatible with Blade Tech, GX Holster, LS Holsters, Weber Tactical and Comp Tac stuff.
What are the differences in the Belt Mount Options?
What are the differences in the Belt Mount Options?
We offer a few options for belt mounts on the Boss holster. The standard aluminum belt plate will come with all of the holsters regardless if you choose one of the options mounts. Something to consider if you go with a non-standard belt mount you may want to go with a shorter Offset Spacer like the 1/4" to stay withing the USPSA rules.
|
The Boss Standard Belt Mount is included with all orders. This belt plate is cut for a standard 1.5" competition belt (DAA, CR Speed, Ghost). The spacing between the screws will accommodate a 1.75" belt. |
The Blade-Tech Tek-Lok Belt Mount is a great Quick Detach option. These mounts are adjustable and can accommodate 1.25"-2" belts We generally recommend going with the 1/4" offset spacer option with this mount. |
|
The Comp-Tac PLM Belt Mount is a great Quick Detach option. These mounts are adjustable and can accommodate 1.25"-2" belts We generally recommend going with the 1/4" offset spacer option with this mount |
The Safariland QLS Belt Mount work with the QLS Receiver. You can quickly swap holsters when using the Safariland QLS system. This option includes the fork only. We generally recommend going with the 1/4" offset spacer option with this mount |
Which Offset length should I choose?
This refers to the length of the spacers between the long Boss plate and the Y-Plate that attaches to the holster. The 1/2" spacers are a pretty safe bet for most firearms out there to keep you within the rules for USPSA.
If you go with one of the options mounts (Tek-Lok, PLM, ELS) we would recommend choosing the 1/4" spacers to keep your holster within the rules for USPSA.
We have seen the 3/4" work well for most models, and may work with Tek-Lok & PLM mounts.
We have found the 1" spacers to work with most models but you should measure your setup to insure it falls within the USPSA rules.
You can always just buy the Spacer Hardware Kit here and try the other options.
What is the optional Baller Ball Joint?
Upgrade your Boss Holster Hanger with the new release from Shockbottle, the Boss Baller Ball Joint.
This ball joint upgrade for your Boss Hanger allows you to adjust the angle of the holster and still raise and lower it as you expect with the Boss Holster Hanger.
You can use the ball joint instead of the spacers on your current rig!
 |
 |
What is the optional Aluminum Thigh Pad?
Comfort and Adjustability Boss Holster Hanger Aluminum Thigh Pad features a unique design that allows you to adjust the spacing of your Boss holster hanger to your personal preference, providing maximum comfort and flexibility.
 |
 |
How to do mount a Safariland QLS Fork or Receiver?
The versatile Boss Holster Hanger is designed to offer multiple mounting options for the Safariland QLS system. It facilitates the attachment of the Safariland QLS Fork to the long plate that is included in the kit, thereby eliminating the need for any additional parts or unique configurations.
For those seeking a flexible mounting solution that allows for easy swapping of holsters while keeping the hanger firmly attached to your belt, we offer the Safariland Y-Plate option. With this, you can conveniently mount the Safariland QLS Receiver to the Y-Plate, as demonstrated in the photographs below.
This powerful combination of utility and adaptability makes the Boss Holster Hanger an essential tool for enhancing your holster mounting experience.
 |
 |
 |
Instructions
1. Attach Y-plate to holster body through three large holes on the Y-plate using supplied short round-head screws to the backers included with your holster.
2. Attach Y-plate to slotted hanger plate using supplied long screws and spacers (do not install lock washers yet). Screw heads should be on the rounded side of the hanger plate, one screw in a center hole and the other in the corresponding curved slot.
3. Hold belt inside belt plate cutout and install onto main hangar plate with 4 flat-head screws, solidly mounting holster and hanger to belt.
4. Test location of holster with unloaded firearm. Adjust to preferred height and tilt by changing screw positions on the main hangar plate and Y-plate. Verify position meets rule requirements
5. Mark position of long screws lightly with a pencil and then remove and re-install the long screws with a lock washer underneath the screw heads. Apply threadlocker to all screws.
* Verify firearm position meets appropriate rule requirements
- #1:
- Attach Y-plate to holster body through three large holes on the Y-plate using short round-head screws
- #2:
- Attach Y-plate to slotted hanger plate using long screws and spacers (do not install lock washers yet). Screw heads should be on the rounded side of the hanger plate, one screw in a center hole and the other in the corresponding curved slot.
- #3:
- Hold belt inside belt plate cutout and install onto main hangar plate with 4 flat-head screws, solidly mounting holster and hanger to belt.
- #4:
- Test location of holster with unloaded firearm. Adjust to preferred height and tilt by changing screw positions on the main hangar plate and Y-plate. Verify position meets rule requirements
- #5:
- Mark position of long screws lightly with a pencil and then remove and re-install the long screws with a lockwasher underneath the screw heads. Apply threadlocker to all screws.
139 Reviews
-
Great product
thank you for your quick answer! shipping to europe was less than a week. highly recommended!
-
Solid
Good solid mount. Heavy duty and durable.
-
The Best
Great hanger and mount. Ridgid design keeps draws smooth with no holster flop. Highly recommend
-
superb upgrade
I purchased this for my Bladetech Revolution Glock 34 (paddle) holster. Easy installation, used the Tek-lok attachment. The assembly sits tight and well on my competition belt. Superb product.
-
Great hanger
Wish I had found this hanger 6 months ago and trying two other brands. Great product!!
-
Very rigid and well constructed. Excellent value!
I'd been looking for a more robust hanger than the one that ships with the Comp Tac International holster. I ran the plastic one for a few months and grew to dislike the flexing during my draw stroke, and wanted to make some tweaks to the positioning, which it cannot do. Add to that I was upgrading to a Safariland ELS belt system (which the Comp Tac drop-offset won't attach to) and I needed a new system. I reviewed a number of other options that were more expensive, many of which were not as adjustable. Someone recommended the BOSS hanger and after reviewing it I was sold. Extremely well constructed from solid metal, very simple yet incredibly adjustable. Took only a few minutes to assemble and hang from the belt. I immediately noticed the difference in the flex during the draw and I much prefer the rigidity while moving. I highly recommend this rig to anyone, whether you're looking at this low price point or not.
-
Better than Expected!
From all the great reviews I read, I expected a good product. Happily I was not let down, the hanger is stronger than I expected for this price point.
-
best holster mount out there
this setup works great, I love it. I have 2 one for 3 gun and one for uspsa.
-
The Best Way to Mount Your Holster
This is as good as it gets. It makes for an unbelievably setup. Well worth the money.
-
Solid
Used the BladeTech DOS with a BladeTech holster, but never was comfortable with the flex. Switched the holster to this and everything works as it should. Felt the bottom of the mount against my leg occasionally at first, but didn't notice it later as the practice round went on. If I feel it again, I will put a small piece of thick leather on the end. I'm glad I bought this product.
-
outstanding!! but...needs lnger screws!!!!!!
I was recommended this hanger by a fellow shooter and he was right on both points. He said this Boss Hanger is the best out there!! BUT... he said the machine screws holding it on the belt are too short, they strip out and rip off the 1 or 2 threads that are holding it on. I tried it out for several months and BAM he was right. If they don’t start shipping with longer screws, just go to a hardware store and get 4 Machine Screws M5-0.8x14mm (or 16mm) at @ $.50/each and problem solved!
-
Great Product
The BOSS Hanger is a high quality product. They are easy to work with as well.
